(818) 886-3755 [email protected] Northridge, CA — Adjacent to LA Aerospace Corridor
AS9100DISO 9001:2015
Request a Quote (818) 886-3755
AS9100D & ISO 9001:2015 Certified

Aerospace
Temperature
Sensors

Flight-critical RTD and thermocouple assemblies manufactured under AS9100D quality management. Full material traceability, NIST-traceable calibration, and First Article documentation available for every aerospace deliverable. Northridge, CA — embedded in the heart of the North American aerospace manufacturing corridor.

AS9100D ACTIVE ISO 9001:2015 ACTIVE NIST TRACEABLE FAIR AVAILABLE
CERTIFICATION & DOCUMENTATION STATUS
AS9100D — Rev D:2016
ACTIVE
ISO 9001:2015
ACTIVE
NIST-Traceable Calibration
STANDARD
Certificate of Conformance (COC)
STANDARD
Material Heat/Lot Traceability
STANDARD
FAIR — AS9102 First Article
ON REQUEST
Calibration Certificate w/ Uncertainty
ON REQUEST
Submit Aerospace RFQ

The Certification and Proximity Your Program Demands

Thermometrics Corporation has held AS9100 certification since 2012, with current registration to AS9100D (Rev D:2016) — the most current revision of the aerospace quality management standard. Our quality management system was built around the requirements of aerospace customers: configuration control, product traceability, inspection documentation, and nonconformance disposition.

Located in Northridge, CA, we operate within 30 miles of the densest concentration of aerospace and defense prime contractors in North America. For AOG situations, engineering clarification, and first article submission, proximity to your facility translates directly to faster program response.

View Quality System
01
Dual AS9100D + ISO 9001:2015 Certification
Most temperature sensor manufacturers hold ISO 9001 only. AS9100D adds approximately 100 aerospace-specific requirements covering product safety, reliability, configuration control, and first article inspection — requirements your purchasing department's approved supplier list demands.
02
Full Material Traceability to Raw Stock
Heat lot records, material certifications, and supplier documentation maintained for every raw material — sheath alloy, sensing element, insulation, and termination hardware. Traceable from raw stock through final assembly per AS9100D clause 8.5.2.
03
Cryogenic Qualification Testing Capability
In-house capability for environmental qualification testing to -196°C (liquid nitrogen) per customer-defined ATP. Data packages include calibration readings at multiple temperature setpoints with NIST-traceable reference. Critical for launch vehicle, satellite, and cryogenic propulsion applications.
04
Northridge, CA — Aerospace Corridor
30 miles from Northrop Grumman, Lockheed Martin Skunk Works, Boeing Defense, SpaceX Hawthorne, and Raytheon facilities. Same-day delivery available. Engineering team available by phone for AOG and critical-path requirements during Pacific Time business hours.
05
Custom Configuration Engineering
Non-standard sheath OD/wall thickness, Mil-spec electrical connectors, hermetic seals, high-temperature braid-over-sheath designs, and hybrid RTD/thermocouple assemblies — engineered to customer drawing with DFM review included at no charge.

Aerospace Manufacturing Capabilities

Full-spectrum capability from standard catalog configurations to engineered-to-drawing assemblies with complete AS9100D documentation packages.

🌡️

RTD Assemblies

PT100 / PT1000 per IEC 60751
Class A and Class AA tolerances
2-, 3-, and 4-wire Kelvin configurations
Thin-film and wire-wound elements
Cryogenic rated to -196°C
Inconel 600/625, 316 SS sheaths
⚡

Thermocouple Assemblies

Types K, J, E, T, N, R, S, B, C per IEC 60584
MIMS (Mineral Insulated) construction
Grounded, ungrounded, exposed junction
Noble metal types to 1700°C
Sheath OD from 0.5mm to 12.7mm
Mil-spec connector terminations
🔬

Environmental Testing

Cryogenic testing to -196°C (LN₂)
Elevated temperature to +850°C
Vibration and mechanical shock
Pressure/leak testing
Thermal cycling qualification
Customer-defined ATP execution
📋

Documentation

Certificate of Conformance (COC)
Material certs with heat/lot traceability
NIST-traceable calibration certificate
FAIR per AS9102 on request
Dimensional inspection records
Special process certifications
⚙️

Custom Engineering

Non-standard sheath geometries
Hermetic seal assemblies
Hybrid RTD/TC combinations
Mil-spec connector integration
High-pressure rated designs
DFM review at no charge
🚀

Program Support

AOG / expedited order fulfillment
Next-day delivery from Northridge CA
Direct engineering-to-engineering support
Prototype to production transition
Long-term supply agreement support
On-site qualification support

Every Deliverable Fully Documented

Under AS9100D, documentation is not optional — it is integral to the product. Every aerospace shipment from Thermometrics includes a baseline documentation package, with expanded documentation available on purchase order specification.

Procurement teams: specify documentation requirements on your purchase order or RFQ. Our quality team will confirm applicability and include all required records with your shipment.

Request Quote + Documentation Spec
Certificate of Conformance (COC)
Signed statement of conformance to purchase order, applicable specifications, and referenced standards. Includes revision level, quantity, and authorizing signature.
✓ STANDARD — INCLUDED WITH EVERY SHIPMENT
Material Certifications — Heat/Lot Traceability
Mill certifications for all sheath alloys (Inconel, SS), sensing elements, and insulation materials. Heat lot numbers traceable from raw stock through final assembly.
✓ STANDARD — INCLUDED WITH EVERY SHIPMENT
Calibration Certificate — NIST Traceable
Resistance or EMF measurements at specified temperature setpoints compared against NIST-traceable reference standards. Uncertainty budget expressed at k=2 (95% confidence).
◆ ON REQUEST — SPECIFY ON PURCHASE ORDER
First Article Inspection Report (FAIR)
Complete dimensional, material, and functional inspection per AS9102. Ballooned drawing with measured data. Required for new part number qualification on most aerospace programs.
◆ ON REQUEST — SPECIFY ON PURCHASE ORDER
Acceptance Test Data Package (ATP)
Completed test records for customer-defined Acceptance Test Procedures including environmental, electrical, and functional tests. Signed and dated by QA.
◆ ON REQUEST — CUSTOMER ATP REQUIRED
Special Process Certifications
Welding certifications per AWS D17.1, cleaning certifications per ASTM or customer spec, and other special process records as required by purchase order.
◆ ON REQUEST — SPECIFY ON PURCHASE ORDER

Flight-Critical Temperature Sensing Applications

From cryogenic propellant systems to high-temperature turbine inlet measurement — Thermometrics sensors operate across the full aerospace temperature spectrum.

🚀

Launch Vehicle & Propulsion

Cryogenic propellant (LO₂, LH₂, LCH₄) temperature measurement, engine compartment thermocouple harness assemblies, and propellant tank ullage temperature sensing. Requires cryogenic rated construction, low thermal conductivity lead wires, and AS9100D documentation.

Sensor Type4-Wire RTD / Type K-J TC
Temperature Range-196°C to +500°C
Sheath MaterialInconel 600 / 304 SS
DocumentationAS9100D COC + NIST Cal Cert
✈️

Aircraft Environmental Control

Cabin air temperature sensing, bleed air temperature, fuel temperature monitoring, hydraulic fluid temperature, and oil temperature measurement for aircraft environmental control and engine monitoring systems.

Sensor TypePT100 RTD 3-Wire or 4-Wire
Temperature Range-55°C to +300°C
ToleranceClass A per IEC 60751
DocumentationCOC + Material Certs + FAI
🛰️

Satellite & Spacecraft

On-orbit thermal monitoring, solar panel temperature, battery thermal management, and structural temperature sensing for satellites and spacecraft. Requires radiation-qualified materials, outgassing compliance, and complete AS9100D traceability.

Sensor Type4-Wire PT100 / Thin-Film
Temperature Range-120°C to +150°C
ConstructionLow-outgassing materials
DocumentationFull AS9100D package
🏭

Ground Support Equipment

Propellant servicing equipment, engine test stands, cryogenic dewar temperature monitoring, and environmental test chamber instrumentation. AS9100D documentation available for GSE hardware entering flight program supply chains.

Sensor TypeRTD or Thermocouple to spec
Temperature Range-196°C to +600°C
Sheath MaterialPer application requirement
DocumentationAS9100D or ISO 9001

Aerospace Temperature Sensor Configurations

AS9100D CERTIFIED
4-Wire Aerospace RTD Assembly
ElementPT100 · IEC 60751
Configuration4-Wire Kelvin
ToleranceClass A
SheathInconel 600
Range-196°C to +600°C
AS9100D CERTIFIED
Type K MIMS Thermocouple Assembly
TypeType K · Chromel-Alumel
ConstructionMIMS · Mineral Insulated
JunctionGrounded / Ungrounded
Sheath OD1.0mm to 6.35mm
Range-200°C to +1260°C
AS9100D CERTIFIED
Cryogenic RTD Assembly
ElementPT100 · 4-Wire
ToleranceClass A · IEC 60751
Min Temp-196°C (LN₂)
Lead WireLow-thermal-conductivity
TestingCryogenic ATP available

Aerospace Procurement FAQ

Common questions from aerospace procurement and engineering teams. Contact our team directly for program-specific requirements.

AS9100D is the Quality Management System standard specific to aviation, space, and defense industries, published by SAE International and IAQG (International Aerospace Quality Group). It is based on ISO 9001:2015 with approximately 100 additional requirements addressing aerospace-specific concerns: product safety, risk management, configuration control, key characteristics, first article inspection, and product monitoring.

Most aerospace prime contractor approved supplier lists (ASL) and purchasing requirements explicitly require AS9100 certification for suppliers of flight hardware and flight-critical components including temperature sensors. ISO 9001 alone is typically insufficient for flight hardware supply chains.

A Certificate of Conformance (COC) is a formal declaration that the delivered hardware conforms to the requirements of the purchase order and applicable specifications — it does not contain actual measured data. A calibration certificate contains actual measurement data: resistance readings (for RTDs) or EMF values (for thermocouples) measured at specified temperature setpoints, compared against a NIST-traceable reference standard, with a stated measurement uncertainty.

For most aerospace applications, both are required. Specify both on your purchase order or RFQ and we will include them in the documentation package.

Yes. First Article Inspection Reports per AS9102 are available on purchase order specification. Our quality team will complete the FAIR documentation — including ballooned drawing, dimensional records, material certifications, and functional test data — prior to shipment of the first production article. FAIRs are required for new part numbers on most aerospace programs and are especially important for flight hardware qualification.

Specify "FAIR required per AS9102" on your purchase order. Lead time for FAIR documentation adds approximately 3–5 business days to standard production lead time for most configurations.

For Aircraft on Ground (AOG) and critical-path program requirements, call us directly at (818) 886-3755 during Pacific Time business hours. Stock configurations can ship same-day via UPS Next Day Air or FedEx Priority One. For non-stock configurations, our production team will assess current capacity and provide a committed lead time within two hours of inquiry.

Our Northridge, CA location allows delivery to most Southern California aerospace facilities (Northrop Grumman, Boeing, Lockheed, Raytheon, SpaceX) within 24 hours even for same-day shipped orders.

Submit Your Aerospace RFQ Today

AS9100D documentation package included. Response within one business day.