(818) 886-3755 [email protected] Northridge, CA
AS9100DISO 9001:2015
AMS 2750F · NADCAP · Heat Treating

Thermocouples for
AMS 2750
Compliance

Thermocouple assemblies and RTD sensors for aerospace heat treating, atmosphere furnace processing, and industrial metal treatment — manufactured to support AMS 2750F pyrometry requirements and NADCAP audit documentation. Type K, N, R, and S available in Inconel sheaths with Class 1 tolerance.

AMS 2750F Thermocouple Requirements
SAT SensorsClass 1 — highest accuracy
Load TCsClass 1 or Class 2 per furnace class
Control TCsCalibrated, traceable, per TUS zone
Over-Temp TCsIndependent circuit, calibrated
Max Use TempPer type — K: 1260°C, N: 1300°C
Wire GradeSpecial limits of error (SLE)
DocumentationCOC + cal cert — NADCAP acceptable
AMS 2750F Pyrometry Standard

Understanding AMS 2750F Thermocouple Requirements

AMS 2750F (Pyrometry) is the SAE Aerospace Material Specification that governs temperature measurement and control in aerospace heat treating processes — including annealing, aging, solution treating, stress relieving, brazing, and precipitation hardening of aerospace alloys.

The standard defines five furnace types (Type A through E) based on temperature uniformity tolerance, and establishes requirements for thermocouple type, calibration frequency, temperature uniformity surveys (TUS), and system accuracy tests (SAT). NADCAP audits verify compliance with AMS 2750F for heat treating suppliers to aerospace primes.

Thermometrics supplies thermocouples that meet the tolerance, calibration, and documentation requirements for AMS 2750F applications. Each thermocouple is supplied with a Certificate of Conformance confirming IEC 60584-2 tolerance class, and NIST-traceable calibration data is available on request for SAT and load sensor qualification.

Request AMS 2750 Sensors →
AMS 2750F — Thermocouple Type Tolerance Reference
TC TypeAlloysIEC ClassTolerance at 1000°CAMS Use Case
KChromel/Alumel–200 to +1260°CClass 1±4.0°CGeneral, control, load TCs below 1100°C
NNicrosil/Nisil–270 to +1300°CClass 1±4.0°CPreferred over K for long-term stability, minimal drift
RPt13%Rh/Pt–50 to +1768°CClass 1±1.0°C*SAT reference, precision, high-temp furnace
SPt10%Rh/Pt–50 to +1768°CClass 1±1.0°C*SAT reference, NIST traceable calibration reference
BPt30%Rh/Pt6%Rh+600 to +1820°CClass 2±3.0°CUltra-high temp vacuum/brazing furnaces above 1600°C

*Noble metal Class 1 tolerance: ±1.0°C or ±[1+0.003(t–1100)]% — whichever is greater. Class 1 required for SAT sensors in most AMS 2750F furnace classes.

Thermocouple Type Selection

Which Type for Your Furnace?

Type selection for heat treating applications is driven by maximum process temperature, atmosphere (oxidizing, reducing, vacuum, inert gas), required long-term stability, and AMS 2750F furnace class. Thermometrics stocks all standard types in MIMS construction.

K
CHROMEL / ALUMEL · IEC 60584
–200°C to +1260°C

The most widely used thermocouple type in heat treating. Good sensitivity (~41 µV/°C), broad temperature range, and wide instrument availability. Susceptible to the "K-effect" — short-range ordering between 200–600°C causing negative EMF drift in long-term service. Calibration intervals per AMS 2750F account for this drift mechanism.

HARDENING · TEMPERING · AGING · ANNEALING below 1100°C
N
NICROSIL / NISIL · IEC 60584
–270°C to +1300°C

Engineered as the long-term stability upgrade to Type K. The Nicrosil/Nisil alloy system was specifically formulated to eliminate the short-range ordering transformation responsible for Type K drift above 300°C. Demonstrates 3–10× less drift than Type K over equivalent service life — reducing required calibration frequency and improving process consistency. Preferred for new furnace installations above 500°C.

PREFERRED FOR NEW INSTALLS · HIGH-TEMP · LONG SERVICE
R&S
Pt-Rh / PLATINUM · NOBLE METAL
–50°C to +1768°C

Platinum-rhodium noble metal thermocouples provide the highest accuracy and long-term stability of any base-metal or noble-metal type in oxidizing atmospheres. Required for SAT (System Accuracy Test) reference sensors in many AMS 2750F furnace classes. Calibration traceability to NIST ITS-90 is straightforward due to inherent stability. Higher material cost than base metals — typically reserved for SAT and control circuits.

SAT REFERENCE · CALIBRATION · HIGH-PRECISION CONTROL
B
Pt30%Rh / Pt6%Rh · NOBLE METAL
+600°C to +1820°C

Type B is uniquely suited for ultra-high temperature furnace applications in vacuum or inert gas atmospheres above 1600°C — vacuum brazing furnaces, high-temperature solution treating of refractory alloys, and ceramic sintering. Very low sensitivity (~6 µV/°C) and near-zero EMF at room temperature — requires careful instrument setup. Not suitable for reducing atmospheres.

VACUUM BRAZING · ULTRA-HIGH TEMP · ABOVE 1600°C
J
IRON / CONSTANTAN · IEC 60584
–40°C to +750°C

Type J has high sensitivity (~52 µV/°C) and good performance in reducing and vacuum atmospheres below 750°C where Type K would oxidize preferentially. Common in older furnace installations. The iron positive leg oxidizes rapidly above 550°C in air — maximum continuous use in oxidizing atmosphere is 500°C. For new installations above 500°C in oxidizing atmosphere, Type K or N is preferred.

REDUCING ATMOSPHERE · BELOW 750°C · LEGACY SYSTEMS
C
W5%Re / W26%Re · REFRACTORY
0°C to +2315°C

Tungsten-rhenium thermocouples achieve the highest temperature measurement range of any standardized type — to 2315°C in vacuum or inert gas. Required for vacuum sintering, crystal growing, and refractory metal processing. Critical limitation: tungsten oxidizes catastrophically above 260°C in air — must never be exposed to oxygen or moisture at elevated temperature. Brittle at room temperature after high-temperature service.

VACUUM/INERT ONLY · SINTERING · REFRACTORY METALS
Process Applications

Heat Treating & Thermal Processing

✈️
Aerospace Heat Treating

Solution treating, aging, and annealing of titanium, aluminum, and nickel superalloys per AMS specifications. NADCAP supplier support documentation available.

TYPE K/N/R · AMS 2750F · CLASS 1 · NIST CAL
⚙️
Atmosphere Furnace Processing

Carburizing, nitriding, carbonitriding, and neutral hardening in controlled atmosphere furnaces. Sheath material selected for atmosphere compatibility — Inconel 600 for carburizing, 304 SS for neutral.

TYPE K · INCONEL 600 SHEATH · ATMOSPHERE COMPATIBLE
🔥
Salt Bath Heat Treating

Immersion temperature measurement in molten salt quench and austempering baths. Inconel 600 sheath resists molten salt corrosion. MIMS construction provides pressure integrity against bath agitation.

TYPE K · INCONEL 600 · MIMS IMMERSION
🏭
Vacuum Furnace Processing

Vacuum brazing, vacuum annealing, and vacuum hardening. Type R/S for precision control circuits. Type B above 1600°C. Type C for refractory metal processing to 2315°C.

TYPE R/S/B/C · VACUUM COMPATIBLE · NOBLE METAL
🔩
Tempering & Stress Relieving

Low-temperature tempering (150–700°C) and stress relieving of steel and stainless steel. Type K Class 1 or Type N for maximum measurement consistency across multi-zone furnaces.

TYPE K OR N · CLASS 1 · MULTI-ZONE
🌡️
Temperature Uniformity Survey (TUS)

Multi-point load TCs for TUS qualification per AMS 2750F. Supplied in sets with individual calibration certificates. Special limits of error (SLE) wire grade available for tightest tolerance.

TYPE K/N · SLE GRADE · INDIVIDUAL NIST CAL CERTS
📐
System Accuracy Test (SAT)

Reference thermocouples for SAT comparison against control and recording thermocouples per AMS 2750F paragraph 3.4. Noble metal Type R or S with current calibration certificate and uncertainty statement.

TYPE R OR S · NIST CAL · UNCERTAINTY STATEMENT
🔬
Induction Hardening

Fast-response thermocouples for surface temperature measurement during induction hardening — exposed junction or small OD MIMS for sub-second response in rapidly cycling applications.

TYPE K · EXPOSED JUNCTION · FAST RESPONSE
Recommended Products

Standard AMS 2750F Configurations

Stocked configurations for common heat treating sensor requirements. NIST-traceable calibration data available on request. Sets of matched TCs available for TUS applications.

TMC-TC-K-IN600-CL1
Type K — Inconel 600, Class 1
AMS 2750F control & load TC · Most common
TypeType K · Chromel/Alumel
ConstructionMIMS, ungrounded junction
SheathInconel 600 (UNS N06600)
ToleranceClass 1 · ±1.5°C or ±0.4%|t|
Temp Range–200°C to +1260°C
OD Options1.6 mm, 3.18 mm, 6.35 mm
DocumentationCOC standard; NIST cal on request
Full Specs →
TMC-TC-N-IN600-CL1
Type N — Inconel 600, Class 1
Preferred for long-term stability · Above 500°C
TypeType N · Nicrosil/Nisil
ConstructionMIMS, ungrounded junction
SheathInconel 600 (UNS N06600)
ToleranceClass 1 · ±1.5°C or ±0.4%|t|
Stability3–10× less drift than Type K
Temp Range–270°C to +1300°C
Full Specs →
TMC-TC-R-NOBLE-SAT
Type R — SAT Reference Sensor
AMS 2750F SAT · NIST calibration included
TypeType R · Pt13%Rh / Pt
ConstructionMIMS, ungrounded junction
ToleranceClass 1 · ±1.0°C or ±0.25%
Temp Range–50°C to +1768°C
CalibrationNIST-traceable cal cert standard
DocumentationCOC + NIST cal + uncertainty statement
Full Specs →

AMS 2750F Thermocouples — Ready to Quote

Type K, N, R, S in Inconel 600 sheath. Class 1 tolerance. NIST cal available. TUS sensor sets. NADCAP documentation support.